Privacy Policy

Last updated: October 2026. This business ("we") respects your privacy. This policy says what we collect through this site and our phone line, and how we use it.

📞 Talk to an HVAC Specialist: (983) 900-5808

Frequently Asked Questions

How much does a furnace repair cost?

Most furnace repairs run $189 to $780. Igniters, sensors, and switches land in the low hundreds. Blower motors and boards cost more. The price is set in writing at the visit, before work starts.

How much does a new furnace cost in Highlands Ranch?

Most installs run $4,800 to $8,500 for one system. The vent plan and the efficiency class move the price most. The permit and haul-away are in the price.

How much does a new AC cost?

Most installs run $5,200 to $9,800 for one system. Size, efficiency, and duct state move the price. A load check sets the size; we never size from the old unit's label.

Why does altitude matter for a furnace?

At 5,900 feet the air holds less oxygen. Gas pressure and combustion air must be set for thin air. A sea-level setup soots, locks out on cold nights, and can be a safety risk.

What is the $5,000 rule?

Multiply the age of the system by the repair quote. If the result passes $5,000, a swap is worth a hard look. We show both prices so you can run the math yourself.

Do heat pumps work in Colorado cold?

Cold-climate models hold heat down to the cold snaps we get a few nights a year. A dual-fuel plan keeps a gas furnace for those nights. We show the cost math in the open.

What Does My HVAC Project Cost?

HVAC work is priced per job or per system — repairs by the part that failed, installs by the system and its efficiency tier. Here are the ranges we see on real jobs around Highlands Ranch, and a calculator built on the same numbers.

Furnace & AC Repair

Most repairs land $189 to $780. Wear parts — igniters, sensors, capacitors, contactors — run $189 to $400; a blower motor or control board runs $400 to $780; a heat pump repair runs $220 to $850. The diagnostic is in every range here, and you get one price in writing before work starts.

Furnace Installation

A standard 80% AFUE furnace runs $4,800 to $6,500 installed; a 96% condensing furnace runs $6,500 to $8,500, PVC vent rework included. Every install is sized by a load check and set up for 5,900 feet — permit and haul-away are in the price.

AC Installation & Replacement

A standard 14–15 SEER2 system runs $5,200 to $7,900; a high-efficiency variable-speed system runs $7,500 to $9,800. Sized to your house and your ducts by a load check — never from the old unit's label.

Heat Pump Installation

A ducted heat pump runs $7,500 to $11,000; a cold-climate dual-fuel system — pump plus your gas furnace as backup — runs $9,500 to $14,000. The change-over point is set with you, and rebate lines are shown apart from the price on the quote.

Ductless Mini-Splits

A single-zone system for one problem room runs $3,800 to $6,500; a multi-zone system for two to four rooms runs $6,500 to $12,000. No ducts to run, and each room gets its own setting.

Maintenance & Tune-Ups

A seasonal tune-up runs $129 to $189 a system: sensors, start parts, coils, drains, and gas safety checked before they fail at the worst time. A weak part found in fall costs a fraction of the same part on the coldest night of the year.

What Moves the Price

  • Efficiency tier. A 96% condensing furnace or an 18+ SEER2 AC costs more up front than the standard tier — the vent rework, the second heat exchanger, and the variable-speed motor are real hardware. The written quote shows both tiers side by side.
  • The $5,000 rule. Multiply the age of your system by the repair quote. If the result passes $5,000, a swap is worth a hard look. We show both prices — repair and replacement — so you can run the math yourself.
  • Altitude. At 5,900 feet the air holds less oxygen. Gas pressure and combustion air are set for thin air on every install and checked on every furnace tune-up. A sea-level setup soots and locks out on cold nights.
  • Duct state. Leaky or undersized ducts waste a new system's output. Ducts are checked on the site visit; sealing at the plenum is small work, a full duct run is its own line on the quote — never folded into the system price.

These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.

A note on sizing. Every install here is figured off a load check on your house — square feet, windows, ducts, and our 5,900-foot altitude — not off the old unit's label. An oversized system short-cycles; an undersized one never catches up on the coldest night. The load check is part of the site visit, before any price is set.

Estimate Your Project

1 · Pick your project

Emergency calls — no heat in a cold snap, no cool in a heat wave — price off this same panel. The price is set in writing at the visit, before work starts.

Free — no obligation. Your calculator numbers ride along with the request.

What we collect

When you send a form or call us, we collect what you give us: your name, phone, email if you give one, and a note on the work you want. If you use the quote tool, your picks are sent with the form so the shop can see them.

How we use it

We use it to call you back, book a site check, write a quote, and do the work. That is all.

What we never do

We do not sell, rent, or trade your details. We share them only with the crew who need them to do your job, and when the law says we must.

Your choices

Ask us at any time what we hold on you. Ask us to fix it or wipe it. Call the phone on this site and we will take care of it.

📞 (983) 900-5808