Heating and Cooling in Highlands Ranch, Run Step by Step

An HVAC job here runs in six steps: first call, site visit, written proposal, scheduling, the work, and the final walkthrough. This page shows each step in full. You see who calls whom, how long each step takes, and what you need to do. Most repairs run $189 to $780. Most installs run one day. Highlands Ranch sits at about 5,900 feet, and that altitude shapes each step, from gas setup to sizing.

Highlands Ranch homes sit at about 5,900 feet, where thin air changes how a furnace burns and how an air conditioner charges. Every system we service or fit here is checked and set for this altitude.

From Northridge and Westridge to Southridge and the Backcountry, most houses here were built from the 1980s through the 2000s — which means a lot of original furnaces and air conditioners are at the age where repair-or-replace is a real question. We will walk you through the honest math either way.

📞 Talk to an HVAC Specialist: (983) 900-5808

Whatever the job, it runs the same way: a written price before work starts, a crew that keeps the work area clean, and a full walkthrough at the end with the system running. The six steps are laid out below.

Six outdoor air conditioning condensers in a row, with a technician servicing one unit

Recent HVAC Projects Around Highlands Ranch

Every project below is priced the same way as the calculator above — pick a card, then run your own system through it.

Furnace, ductwork, and water heater in a home utility room in Highlands Ranch, CO

Furnace Installation — Highlands Ranch

Furnace Installation · Highlands Ranch, CO · 1 day on site, after the home check · October 2025

Pulled the permit, swapped a 22-year-old furnace for a 96% AFUE unit, reworked the vent in PVC, and set gas pressure for altitude. Ducts sealed at the plenum.

Final price: $7,450

Our old furnace ran loud and the upstairs never warmed up. The crew sized the new one off a load check, set it up for the altitude, and sealed the plenum. The upstairs gap closed to one degree — and each line was clear, and the final bill matched it to the dollar.

— Dana, Highlands Ranch
Crew setting a new outdoor AC unit on a rooftop in Highlands Ranch, CO

AC Installation and Replacement — Highlands Ranch

AC Installation · Highlands Ranch, CO · 1 day on site, permit pulled before · July 2025

Ran a load check, swapped a 19-year-old R-22 unit and coil, set the new unit level, charged by weight, and tested room by room. Old unit hauled away.

Final price: $8,150

The old unit used the gas they do not make now, and each summer the repairs got bigger. They sized the new one to the house, not to the old box. The house held 72 on a 95-degree day — the load check is what I tell friends about.

— Tom, Highlands Ranch
Technician checking a heat pump compressor during an installation in Highlands Ranch, CO

Heat Pump Installation — Highlands Ranch

Heat Pump Installation · Highlands Ranch, CO · 2 days on site · February 2025

Fit a cold-climate heat pump with the gas furnace kept as backup, set the change-over point with the owner, and showed the rebate lines apart from the price on the quote.

Final price: $11,900

I wanted off gas for most of the year but I did not trust a pump alone at ten below. The dual-fuel plan keeps the furnace for the coldest nights. The pump carried the house through the fall — it was the first quote that showed me the weak points too.

— Ellen, Highlands Ranch
Gloved hands opening a wall-mounted ductless mini-split indoor unit for service in Parker, CO

Ductless Mini-Split — Parker

Ductless Mini-Split · Parker, CO · 1 day on site · September 2024

Fit a single-zone ductless mini-split in a hot south-facing primary suite — outdoor unit on a pad, one quiet wall head, line set through the wall, charged and tested.

Final price: $4,900

The suite baked every afternoon while the rest of the house was fine, and we did not want ducts torn through the attic. One wall unit, its own setting, done in a day. The room holds its temperature now and the main system rests.

— Rob and Lisa, Parker
Technician inspecting an attic air handler and ducts during a furnace repair in Littleton, CO

Furnace Repair — Littleton

Furnace Repair · Littleton, CO · Same day, about 2 hours on site · April 2024

Tested the full start chain on a no-heat call, found a worn blower motor drawing high amps, fitted a new motor, and re-tested airflow room by room.

Final price: $560

The furnace ran, blew cold, and shut off. They tested in order instead of guessing, showed me the amp draw on the old motor, and priced the swap in writing before touching it. Heat was back the same visit.

— Steve, Littleton
Technician repairing an outdoor AC unit in Castle Rock, CO

AC Repair — Castle Rock

AC Repair · Castle Rock, CO · Same day, about 1 hour on site · January 2024

On a no-cool call, tested the start chain and found a failed capacitor and a pitted contactor. Fitted both from truck stock and ran a full cooling cycle with the owners there.

Final price: $340

The unit hummed and would not start on the hottest Saturday of the summer. Two wear parts, both on the truck, one written price before the work. It started on the first try and held temp all weekend.

— Paul and Jen, Castle Rock

The full job run, step by step

First call

About 10 minutes

You call or send the form. We ask what the system does, how old it is, and which rooms feel wrong. A gas smell or a carbon alarm is flagged at once: leave the house, call for help, then call us.

Site visit

30 to 60 minutes

The tech tests your real system: start parts, charge, coils, gas safety, and air flow. You hear the finding in plain words, with the test values. No work is sold on this visit unless you ask for a price.

Written proposal

Sent the same day

One price in writing. Parts, labor, permit, and haul-away are their own lines. Repair and swap prices are shown side by side on old systems, so the call is yours with real numbers.

Scheduling

About 2 minutes to book

You pick the day and the window: morning, afternoon, or first open day. The office calls the day before to confirm. Bad weather that makes roof or yard work unsafe moves the job at no added cost.

The work

2 hours to 2 days, by the job

Floors are covered and the work area is kept clean. The tech or crew lead is on site the whole job. If the plan must change mid-job, you hear it and the new price before the work goes on, not after.

Walkthrough and check

About 30 minutes

The system runs a full cycle with you there. Air is checked room by room. You learn the filter size and the stat settings. The final bill matches the written quote, line for line.

Try the job tracker

Tap a step to see what happens in it, how long it takes, and your prep list for that stage. Then pick the window you want in the form at the foot of this page. Your pick flows into the form for you.

Job Tracker — Tap a Step

Tap a step to see what happens in it, how long it takes, and your prep list for that stage.

3. Written proposal

6. Walkthrough and check

Pick Your Window

Pick the window you want for the site visit. Your pick flows into the quote form below — no need to type it twice.

No pick yet. The form below takes a pick, too.

Our HVAC services

Each service page opens with that job's own timeline. A repair day is not an install day, and the pages say so.

Crew and gear

Our crews run with a lead tech on each job. The gear list is plain: gauges and meters for charge and gas tests, combustion checks on each furnace job, and parts for the common wear items on the truck. The lead calls the order of the day, and the office keeps you posted if a job runs long. A bit like a good kitchen in a dinner rush: each person has a post, and no one guesses.

Results preview

Our results page logs six jobs in full: the system, the scope, the price, and what the owner said at the end. See the Results page.

Areas we serve

We serve Highlands Ranch plus Littleton, Centennial, Castle Rock, Parker, Lone Tree, and Englewood. Castle Pines, Columbine, Greenwood Village, and Ken Caryl are served from the Service Areas page.

Book Step One: The Site Visit

Call 983-900-5808 or send the form. Pick your window in the form. The office calls the day before your visit to confirm.

Each job is logged step by step, from first call to final walkthrough. You get the written price before work starts.

Book a Site Visit

Pick your window here, or use the picker on the home page and it lands here for you. The office calls the day before to confirm.

Frequently Asked Questions

How much does HVAC repair cost in Highlands Ranch?

Most repairs run $189 to $780. Wear parts like igniters, sensors, and capacitors land in the low hundreds. Blower motors and boards cost more. You get one price in writing before work starts.

How long does a furnace install take?

One day for most homes. The home check comes first, the permit is pulled, and the new unit is set, vented, and tested the same day it goes in.

Do I need to be home for the work?

It helps at the start and at the final check. You do not need to stay all day. The lead needs a phone number that reaches you.

Does altitude change how a furnace is set up?

Yes. At 5,900 feet the air is thin. Gas pressure and combustion air must be set for altitude, or the furnace soots, locks out, and runs short on heat.

What if my system quits at night?

Call us. The emergency page lists the three safe checks to run first. A gas smell or a carbon alarm means leave the house and call for help first.

Do you pull permits?

Yes. System swaps need a permit and an inspection. Both are part of the job, and the fee shows at cost on the quote.

What Does My HVAC Project Cost?

HVAC work is priced per job or per system — repairs by the part that failed, installs by the system and its efficiency tier. Here are the ranges we see on real jobs around Highlands Ranch, and a calculator built on the same numbers.

Furnace & AC Repair

Most repairs land $189 to $780. Wear parts — igniters, sensors, capacitors, contactors — run $189 to $400; a blower motor or control board runs $400 to $780; a heat pump repair runs $220 to $850. The diagnostic is in every range here, and you get one price in writing before work starts.

Furnace Installation

A standard 80% AFUE furnace runs $4,800 to $6,500 installed; a 96% condensing furnace runs $6,500 to $8,500, PVC vent rework included. Every install is sized by a load check and set up for 5,900 feet — permit and haul-away are in the price.

AC Installation & Replacement

A standard 14–15 SEER2 system runs $5,200 to $7,900; a high-efficiency variable-speed system runs $7,500 to $9,800. Sized to your house and your ducts by a load check — never from the old unit's label.

Heat Pump Installation

A ducted heat pump runs $7,500 to $11,000; a cold-climate dual-fuel system — pump plus your gas furnace as backup — runs $9,500 to $14,000. The change-over point is set with you, and rebate lines are shown apart from the price on the quote.

Ductless Mini-Splits

A single-zone system for one problem room runs $3,800 to $6,500; a multi-zone system for two to four rooms runs $6,500 to $12,000. No ducts to run, and each room gets its own setting.

Maintenance & Tune-Ups

A seasonal tune-up runs $129 to $189 a system: sensors, start parts, coils, drains, and gas safety checked before they fail at the worst time. A weak part found in fall costs a fraction of the same part on the coldest night of the year.

What Moves the Price

  • Efficiency tier. A 96% condensing furnace or an 18+ SEER2 AC costs more up front than the standard tier — the vent rework, the second heat exchanger, and the variable-speed motor are real hardware. The written quote shows both tiers side by side.
  • The $5,000 rule. Multiply the age of your system by the repair quote. If the result passes $5,000, a swap is worth a hard look. We show both prices — repair and replacement — so you can run the math yourself.
  • Altitude. At 5,900 feet the air holds less oxygen. Gas pressure and combustion air are set for thin air on every install and checked on every furnace tune-up. A sea-level setup soots and locks out on cold nights.
  • Duct state. Leaky or undersized ducts waste a new system's output. Ducts are checked on the site visit; sealing at the plenum is small work, a full duct run is its own line on the quote — never folded into the system price.

These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.

A note on sizing. Every install here is figured off a load check on your house — square feet, windows, ducts, and our 5,900-foot altitude — not off the old unit's label. An oversized system short-cycles; an undersized one never catches up on the coldest night. The load check is part of the site visit, before any price is set.

Estimate Your Project

1 · Pick your project

Emergency calls — no heat in a cold snap, no cool in a heat wave — price off this same panel. The price is set in writing at the visit, before work starts.

Free — no obligation. Your calculator numbers ride along with the request.

📞 (983) 900-5808