Thermostat Installation & Replacement in Highlands Ranch, CO
Price: $150–$450 fitted. Terms: full price quoted before work; balance due when the job tests right. Time: done in about an hour. Repair note: if a repair beats a swap on cost and life, we tell you.
A smart or simple thermostat fitted right, with the wiring checked. We serve Highlands Ranch first and the suburbs around it, and we size and set every system for work at about 5,900 feet.
📞 Talk to an HVAC Specialist: (983) 900-5808Frequently Asked Questions
Will a smart thermostat save me money?
It saves when you use the schedule and setbacks — most homes see 8–10% off heating and cooling. A stat you never program saves nothing, so we set the first schedule with you before we leave.
My home has no common wire. Can I still go smart?
Yes. Many stats ship with a power adapter, or we can use a spare wire in the cable. We check at the furnace board and tell you the clean route before any work.
What will it cost, in the end?
Most thermostat installation & replacement work lands in the $150–$450 fitted range. You get the exact price after diagnosis and before work starts. The quote is the price — no add-ons at the door.
What Does My HVAC Project Cost?
HVAC work is priced per job or per system — repairs by the part that failed, installs by the system and its efficiency tier. Here are the ranges we see on real jobs around Highlands Ranch, and a calculator built on the same numbers.
Furnace & AC Repair
Most repairs land $189 to $780. Wear parts — igniters, sensors, capacitors, contactors — run $189 to $400; a blower motor or control board runs $400 to $780; a heat pump repair runs $220 to $850. The diagnostic is in every range here, and you get one price in writing before work starts.
Furnace Installation
A standard 80% AFUE furnace runs $4,800 to $6,500 installed; a 96% condensing furnace runs $6,500 to $8,500, PVC vent rework included. Every install is sized by a load check and set up for 5,900 feet — permit and haul-away are in the price.
AC Installation & Replacement
A standard 14–15 SEER2 system runs $5,200 to $7,900; a high-efficiency variable-speed system runs $7,500 to $9,800. Sized to your house and your ducts by a load check — never from the old unit's label.
Heat Pump Installation
A ducted heat pump runs $7,500 to $11,000; a cold-climate dual-fuel system — pump plus your gas furnace as backup — runs $9,500 to $14,000. The change-over point is set with you, and rebate lines are shown apart from the price on the quote.
Ductless Mini-Splits
A single-zone system for one problem room runs $3,800 to $6,500; a multi-zone system for two to four rooms runs $6,500 to $12,000. No ducts to run, and each room gets its own setting.
Maintenance & Tune-Ups
A seasonal tune-up runs $129 to $189 a system: sensors, start parts, coils, drains, and gas safety checked before they fail at the worst time. A weak part found in fall costs a fraction of the same part on the coldest night of the year.
What Moves the Price
- Efficiency tier. A 96% condensing furnace or an 18+ SEER2 AC costs more up front than the standard tier — the vent rework, the second heat exchanger, and the variable-speed motor are real hardware. The written quote shows both tiers side by side.
- The $5,000 rule. Multiply the age of your system by the repair quote. If the result passes $5,000, a swap is worth a hard look. We show both prices — repair and replacement — so you can run the math yourself.
- Altitude. At 5,900 feet the air holds less oxygen. Gas pressure and combustion air are set for thin air on every install and checked on every furnace tune-up. A sea-level setup soots and locks out on cold nights.
- Duct state. Leaky or undersized ducts waste a new system's output. Ducts are checked on the site visit; sealing at the plenum is small work, a full duct run is its own line on the quote — never folded into the system price.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.
A note on sizing. Every install here is figured off a load check on your house — square feet, windows, ducts, and our 5,900-foot altitude — not off the old unit's label. An oversized system short-cycles; an undersized one never catches up on the coldest night. The load check is part of the site visit, before any price is set.
Estimate Your Project
Emergency calls — no heat in a cold snap, no cool in a heat wave — price off this same panel. The price is set in writing at the visit, before work starts.
Permit, haul-away, and the altitude setup are in every price. Vent rework in PVC is in the 96% tier.
New pad, line-set flush, charge by weight, and a room-by-room test are in every price.
Rebate lines are shown apart from the price on your written quote — never netted into these ranges.
One quiet wall unit per room, each with its own setting. Most single-zone jobs run one day.
Sensors, start parts, coils, drains, and gas safety — the parts that fail most, checked before they fail.
Free — no obligation. Your calculator numbers ride along with the request.
Send Your Project to Highlands Ranch HVAC Pros
Your estimate is attached automatically. Add your info and — if you can — a few photos of the project. Photos help us price the job before we ever set foot in the house. Prefer to talk? Call (983) 900-5808.
One job, step by step
Paula's old thermostat overshot by four degrees and short-cycled her furnace chasing its own mistakes. A smart thermostat with a proper common wire — a power extender kit at the furnace — fixed the power problem that makes stats lie. About an hour, with heat and cool calls tested clean.
- Service performed
- Thermostat Installation & Replacement in Highlands Ranch.
- Scope of work
- Smart thermostat fitted with a common-wire adapter at the furnace.
- Materials / products used
- Smart thermostat and power extender kit.
- Size
- Single-stage furnace with AC, one zone.
- Final price
- $315.
- Cost per sq ft
- Not used for thermostat work.
- Turnaround / duration
- About 1 hour.
- Payment terms / financing
- Full price quoted before work; balance due after heat and cool calls test clean.
- Problem found
- Old stat overshot by 4 degrees and the furnace short-cycled.
- Solution delivered
- Smart stat with a proper C-wire; temps now hold within a degree.
- Homeowner first name
- Paula.
- Homeowner city / neighborhood
- Highlands Ranch, CO.
- Homeowner situation (in their own terms)
- The old stat overshot by 4 degrees and the furnace short-cycled. The house swung hot and cold all day.
- Outcome and homeowner reaction
- Temps now hold within a degree at Paula's home. She said the schedule feature paid for the visit faster than she expected.
Signs You Need Thermostat Installation & Replacement
- Thermostat reads wrong or will not hold a setting.
- You want phone control and schedules that save money.
- The old stat was wired for heat only and you added AC.
- Rooms overshoot and undershoot the set temp.
What Usually Causes It
- Many smart stats need a common wire old homes lack.
- A bad stat can short-cycle a good furnace.
- Placement matters — a stat in sun or draft reads the room wrong.
How the Work Goes
- We check your wiring and system type first.
- We fit the new stat, wire or adapt the common wire, and level it.
- We set the schedule with you and test heat and cool calls.
Questions About Thermostat Installation & Replacement
Request Thermostat Installation & Replacement
Prefer to talk? Call (983) 900-5808.
Related services: HVAC Zoning System Installation, Commercial HVAC Repair & Maintenance, and Commercial HVAC Installation & Replacement.
Also serving: HVAC Services in Denver, HVAC Services in Edgewater, and HVAC Services in Federal Heights.
Related Services
AC Installation · AC Repair · Ductless Mini-Split Installation · Emergency HVAC Repair · Furnace Installation · Furnace Repair · Heat Pump Installation and Repair · HVAC Maintenance and Tune-Ups · HVAC Replacement · Indoor Air Quality Services · Air Duct Cleaning · Air Duct Repair & Replacement · Whole-Home Humidifiers · Ductless Mini-Split Repair